To reduce the burden on water supply and wastewater systems by increasing the water efficiency of appliances and water-consuming processes.
* This credit language is drawn from the LEED v4 draft. Where other point totals are noted, this pilot credit is worth 1 point in total. *
Appliance and process water use
Install appliances, equipment, and processes within the project scope that meet the requirements listed in the tables below .
Table 2. Standards for appliances
|Residential clothes washers||ENERGY STAR or performance equivalent|
|Commercial clothes washers||CEE Tier 3A|
|Residential dishwashers (standard and compact)||ENERGY STAR or performance equivalent|
|Prerinse spray valves||≤ 1.3 gpm (4.9 lpm)|
|Ice machine||ENERGY STAR or performance equivalent and use either air-cooled or closed-loop cooling, such as chilled or condenser water system|
gpm = gallons per minute
lpm = liters per minute
Table 3. Standards for processes
|Heat rejection and cooling||No once-through cooling with potable water for any equipment or appliances that reject heat|
|Cooling towers and evaporative condensers||Equip with:
In addition, water-consuming appliances, equipment, and processes must meet the requirements listed in Tables 4 and 5.
Table 4. Standards for appliances
|Kitchen equipment||Requirement (IP units)||Requirement (SI units)|
|Dishwasher||Undercounter||≤ 1.6 gal/rack||≤ 6.0 liters/rack|
|Stationary, single tank, door||≤ 1.4 gal/rack||≤ 5.3 liters/rack|
|Single tank, conveyor||≤ 1.0 gal/rack||≤ 3.8 liters/rack|
|Multiple tank, conveyor||≤ 0.9 gal/rack||≤ 3.4liters/rack|
|Flight machine||≤ 180 gal/hour||≤ 680 liters/hour|
|Food steamer||Batch||≤ 6 gal/hour/pan||≤ 23 liters/hour/pan|
|Cook-to-order||≤ 10 gal/hour/pan||≤ 38 liters/hour/pan|
|Combination oven||Countertop or stand||≤ 3.5 gal/hour/pan||≤ 13 liters/hour/pan|
|Roll-in||≤ 3.5 gal/hour/pan||≤ 13 liters/hour/pan|
Table 5. Standards for processes
|Discharge water temperature tempering||Where local requirements limit discharge temperature of fluids into drainage system, use tempering device that runs water only when equipment discharges hot water
Provide thermal recovery heat exchanger that cools drained discharge water below code-required maximum discharge temperatures while simultaneously preheating inlet makeup water
If fluid is steam condensate, return it to boiler
|Venturi-type flow-through vacuum generators or aspirators||Use no device that generates vacuum by means of water flow through device into drain|
- Participate in the LEEDuser pilot credit forum
- Complete the feedback survey:
NC, CS, Schools, Retail NC, CI, Retail CI, Healthcare:
- Provide a schedule indicating ALL process water equipment. Indicate which types of equipment that are being installed on the project are applicable to the credit and the quantity of equipment which is to be installed. For Healthcare, Schools, Retail and Hospitality projects, include the items in Tables 3& 4 as well.
- Provide a floor plan indicating the location of all process water equipment.
- Submit one-line diagrams of all piping systems associated with the referenced equipment, inclusive of design flow rates for both supply and effluent.
- Provide approved manufacturer's information (i.e. cut sheets, shop drawings, submittals) for each piece of equipment applicable to this credit, indicating at a minimum
water usage, capacity of equipment, and energy star rating (if applicable).
Provide a copy of the purchasing policy, which must include:
- detail on its physical and programmatic scope;
- duration of applicability;
- responsible parties (by individual name or title);
- sustainability goals and objectives;
- procedures and strategies for implementation;
- specific metrics by which performance will be measured; and
- a quality assurance process to evaluate and verify successful implementation of the policy.
Provide the following:
- a log of all existing equipment covered by the credit
- a maintenance plan and log to ensure that the equipment is being properly maintained (and not leaking)
- documentation that at least 20% of all installed equipment and 100% of purchases during the performance period meet the requirements.
- Did your project include any other appliances or process water items that should be included in the credit?
- Were you able to find suitable products at a reasonable cost at the flow rates required?
- Changes made for 2nd Public Comment (08/01/2011):
Added Healthcare to the applicable rating system types
Restructured EBOM requirements based on new EBOM structure for LEED 2012 and
aligned purchasing agreement language with other EBOM purchasing credits.
Separate submittal requirements for NC vs. EBOM
Added Ice Machine requirement (ENERGY STAR) originally in the Appliance & Process Water credit from LEED 2012.
Clarified Discharge Water Temperature Tempering requirement is based on the water leaving the appliance (rather than the tank) to reduce maintenance concerns.
- Changes made for 3rd Public Comment (03/01/2012):
Updated requirements based on changes for 3rd public comments.
Separated Tables 3&4 addressing food service and specialty process water items not usually included in a commercial office building. These requirements only apply to Healthcare, Schools, Retail and Hospitality projects.
Removed some process and appliance requirements for EBOM
- Changes made for 5th Public Comment (01/15/2013):
Updated metrics to align with 5th Public Comment changes to LEED v4
- Changes made based on feedback (03/15/2013):
Modified EBOM requirements to include purchasing logs and inventory of current equipment
Clarified that projects without any applicable equipment are ineligible
Ask questions, share tips, and get notified of new forum posts by joining LEEDuser, a tool developed by BuildingGreen and supported by USGBC!
No sample form available for this credit.View all sample forms